Re: EA6900 New Firmware 1.1.42.158863 ???
I was having problems before the firmware update with the Linksys light constantly blinking but I was always able to connect to the internet. Since the new update the Linksys light stays on and...
View ArticleRe: Password and extra security at sign in
I've had the same experience and what I did was call up their Support . I was told that this is getting fixed and they offered to make an account for me. You may try doing the same if you still have...
View ArticleRe: Issues with EA3500 and RE2000
To further isolate, turn off the RE2000 and remove it from the connected devices list. Once done, refresh the Device list page and check if it shows multiple IP addresses and Mac addresses on the each...
View ArticleRe: E1200 -- 2 of 4 ports problem?
Hi redandpeanut,Good thing it did not cause any damage. I guess they have their own system that checks the entitlement status. They will know if it's still in warranty even if you no longer have the...
View ArticleNeed Help With My Linksys Wireless Router Model # WRTU54G-TM
I don't remember my user name and password to be able to access my wireless routher by typing the ip address in the browser bar where you type in a website to bring up the router. Is there a way to...
View ArticleRe: EA3500 via CCC is difficult to connect
Thanks. Called "Customer Support" had me on the phone for about 15 minutes and wanted to sell me something for $9.95. I told them that all I wanted was to set up the router and that's all but on and on...
View ArticleRe: Need Help With My Linksys Wireless Router Model # WRTU54G-TM
Nope. You must hard reset the router by holding the reset button in back/bottom for 30 seconds and release. Power cycle the router. Now connect back to 192.168.1.1 username blank password 'admin'....
View ArticleEA2700 log file
Time Warner techs have been to my house once a week for a month and a half. They don't seem to know what to do on the Internet side of their business. A couple of times they have tried to blame my...
View ArticleFinding admin page
I have a wrt54g2 router that I want to check some settings and firmware updates. My problem is I do not remember how to get to the web based admin. site. I type in the number 192.168.1.1 that I thought...
View ArticleEA6300 and Wireless Media Streaming
I'm very interested in wirelessly streaming media using a SiliconDust HDHomeRun TV tuner over my home network. Two questions:1. It seems that the 6300 router should provide enough throughput to do...
View ArticleRe: Finding admin page
Hi millturn, what you can do is connect a PC to one of the ports on the router and check your IP settings on that PC.You can do it by going to the Command prompt. On a Windows based computer, you can...
View ArticleRe: Issues with EA3500 and RE2000
It could be the firmware design for the extender. When devices connect to the extender it could either create a new adapter or bridge and forward the Mac address through it's arp implementation.In a...
View ArticleRe: EA6300 and Wireless Media Streaming
Enable WMM support and increase your 5ghz channel width to its maximum. Disable any QOS you may have enabled.
View ArticleRe: RA6700/WUMC710: Multicast IGMP V2 support?
I don't recommend using wireless bridges unless it's too hard to run a line. Hardwired is always more dependable.The setup you listed should work depending on signal strength at the location. 5ghz...
View ArticleRe: Finding admin page
Thank You for the fast response, I did just what you said but my default gateway address shows as two colons( : : )Would you have anymore ideasThanx
View ArticleRe: wumc710 with ea6500, no ip from dhcp
My ISP is Time Warner, but I should probably reiterate that these devices are being used only to stream media from inside the home, so there's no Internet networking really required.
View ArticleRe: wumc710 with ea6500, no ip from dhcp
What you should do is give all your devices behind the extenders and the extenders themselves static ip information. The ip info you give them should be outside the dhcp server range.Example:Dhcp range...
View ArticleRe: Finding admin page
If that is the case, just try accessing 192.168.2.1 or 192.168.0.1. Those are the usual IP addresses being assigned to the router. If nothing works, you may have to unplug the router from the modem for...
View ArticleRe: wumc710 with ea6500, no ip from dhcp
They are all static currently, and have always been, but the IPs are inside the DHCP range and are reserved by the EA6500 - this was recommended to work around the "Device List Bug" that was so...
View ArticleRe: Finding admin page
Thanx again for the response. That worked, my router guide manual has the wrong address, its the .0.1 not.1.1.Thanx again
View Article