Re: Laptop cannot log into WRT120N Router, but ipad can...
I’ve read an article that this is common in the old firmware version and they strongly advised to perform a firmware upgrade. Before doing an upgrade, you need to reset the router button for exactly 10...
View ArticleRe: I created 2 networks by accident. how do i remove the one that doesn't work?
You can check the guest password in the Cisco Connect software that you installed on your computer. To know how, check this link:...
View ArticleRe: Laptop cannot log into WRT120N Router, but ipad can...
Have you tried to clear cache on your laptop? Please disable proxy settings as well. Here's how to disable proxy settings on Mozilla Firefox...
View ArticleRe: Parental Control going nuts (EA3500)
Rebooting the router will clear the DHCP table in case the hostnames aren't updating since the iPads last got an IP.
View ArticleRe: Linksys Connect CD/Downloadable Software compatibility problem with Mac...
Hi bassist71, You may actually do the setup manually. It's done by accessing the setup page of the route through 192.168.1.1 and configuring the settings according to your Internet connection type. If...
View ArticleRe: EA6300 Parental Controls
No such luck with the reboot of the children's computers. The key here is that it just randomly starts blocking any system with parental controls turned on even thought it is not set to block at that...
View ArticleRe: TWO NETWORK ADAPTERS
Is everything working now? You may continue tweaking on the channel settings if you continue to have a difficulty seeing the network.
View ArticleRe: EA4500 too slow?
If you haven't already returned the EA4500 I recommend using the Classic Firmware. If you are having issues with a PPPoe internet connection I have a fix for that. How to install classic firmware
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
Did you look on the cable for any identification? Did you check the model number of your adapter and pull up the specifications and see if it is a 1Gbps card?
View ArticleRe: SPI firewall
Because you are using IPv4 NAT devices behind the router are firewalled by nature regardless. You need to use port forwarding to expose port from lan computers to the internet.
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
Most likely your Desktop has a 10/100 network card.
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
YEA !! I just checked - I have a cat5e cable with a 100Mbps card - so all I need to do is changeout the card for a 1 Gbps card and I am done ? Sounds too easy !
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
You go it :smileyhappy:
View ArticleRe: how to enable EA6700 SNMP
Because they are all cheap home routers and don't need this feature.
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
But ... does this not assume that my motherboard / disc drive etc can push out data that fast ? I have a Dell 9150 ... which is an i7 / windows 7 64 bit machine.
View ArticleRe: Why does my Port say "10/100 Mbps" when it is attached to a Cat 5 cable...
More than enough processing power with that desktop. You should get a transfer rate of about 727mb/s on your LAN. There is some overhead due to the IP frame itself so a full 1Gig shouldn't really be...
View ArticleconectING wires from router(WRT 54G V8 TO MODEM AND TO MY COMPUTER
WHAT WIRES DO I USE TO CONNECT MY ROUTER (WRT 54G V80) TO MY MOTOROLA MODEM AND MY CO MPUTER..II HAVE THE BLUE PLUG ATTACHED TO MY ROUTER IN THE ONE OUTLET AND THEN INTO MY MODEM I HAVE THE SMALL...
View ArticleRe: conectING wires from router(WRT 54G V8 TO MODEM AND TO MY COMPUTER
MODEM's port connected with ethernet cable to the WRT's Internet Port (WAN).Computer connected with ethernet cable to one of the ethernet ports on the WRT labeled 1 through 4.
View ArticleRe: Linksys Connect CD/Downloadable Software compatibility problem with Mac...
Thanks pepper_mint! I finally got it configured manually and this reply is evidence that it's working! Thanks!
View ArticleRe: Router disconnecting
Hi jfarthing, please try to set a different channel settings on the router. You may try to choose from Channels 11,9,3 and 1. The case may be caused by wireless interferences in the area.
View Article