Re: router password for 192.168.D.104
Login to the router using the link below: http://192.168.1.1 username: adminpassword: admin It may just ask for a password depending on the router model. In the wireless section you can view the...
View ArticleRe: Linksys EA6900 (AC1900) "Media Prioritization" Set-up Question
The answer is it all depends on what you are trying to accomplish, as I learned the hard way. For some reason, my Downstream Bandwidth defaulted to 3092 Kbps on my router, even though my actual...
View ArticleRe: Trying but Failing to Set Up USB Disk Drive with E4200v2
At this point, after some time has passed the repeated disk access has settled down. And I appear to have access to the storage. All seems well so far. -Noel
View ArticleClik here to view.
Configuring Routing between E1200 and WRT300N
Hi everyone, I need some help. I have a WRT320N working just fine connecting to the internet and serving my wired and wireless devices. This router is 192.168.1.1 (see attached schematic). I subnet me...
View ArticleRe: EA6300 Output Strength
Thank you - but my router does not have an antenna.... And now it is losing connectivity on almost an hourly basis... I unplug and plug back in... it works for a bit but then back to "limited...
View ArticleRe: Configuring Routing between E1200 and WRT300N
Sort of a novice at thisbut I think you want to connect to the Lan port on the 1200. Leave dhcp turned off.
View ArticleRe: EA 4500 with very low downloadspeed while upload is very high. What to do?
If the previous post solves your problem, but you want Media Priorization on your router, then re-enable it, but make absolutely certain that in your settings you set your Download speed to a value...
View ArticleRe: EA6300 Output Strength
Well actually it does have antennas but they are inside the box and you can't get to them@NO_SCREENNAME@ wrote:Thank you - but my router does not have an antenna.... And now it is losing connectivity...
View ArticleRe: Configuring Routing between E1200 and WRT300N
I tried that, but the same result. I do not want it to just be a switch, but a router. If I make that change, I can ping only the same devices as before.Any other ideas?
View ArticleRe: What characters & symbols are supported in LinkSys WAPs?
As far as I know, it supports 32 to 126 ASCII characters only. Some wireless devices are having a hard time accepting the special characters and symbols. I also agree with Chadster. Include capital...
View ArticleClik here to view.
Re: WRT1900AC - Intermittant Reboots (UK,BT) ******KNOWN ISSUE
Ok so today, I factory reset the router, reloaded FW, factory reset the router again, and set up from scratch. I configured what I needed, IP reservations, set DMZ for my VoIP device, Mixed modes on...
View ArticleRe: WRT1900AC - Sudden Disconnects
Chadster766, what do you have on the network when testing? because what i find is that it has to do with devices and quantities on the network. So basically you can test with a few devices and get...
View ArticleClik here to view.
Re: WRT1900AC - Sudden Disconnects
You are definitely right. In your case you have a lot going on and there is many issues that can be the cause I have noticed a drastic drop in reboot\lockup related post since I've posted the 5Ghz "N...
View ArticleRe: WRT1900AC Speedtest
I do not see where I can change servers on the router. I did try ping the listed severs in Atlanta GA but all came back in the 30 Mbps range
View ArticleRe: WRT1900AC and OpenWrt
RogerSC wrote:BlueNaru21 wrote:Hey there, bartpl. Looks like the link's not working. I'm getting an error 404 (This is not the page you are looking for). Can you send one that works, please? Thanks in...
View ArticleClik here to view.
Re: WRT1900AC and OpenWrt
There's lots of options Go to link below: https://github.com/wrt1900ac/opensource You can choose either Attitude Adjustment (My fav) or Barrier Breaker (Bleeding Edge) Upload the firmware using the...
View ArticleClik here to view.
Re: WRT1900AC and OpenWrt
chadster766 wrote:There's lots of options Go to link below: https://github.com/wrt1900ac/opensource You can choose either Attitude Adjustment (My fav) or Barrier Breaker (Bleeding Edge) Upload the...
View ArticleRe: WRT1900AC running at high loads
Ya, some users are seeing an issue with mode A on 5Ghz so it's been recommended to use single mode N. I've been using mixed and haven't seen this issue as of yet. Some say streaming heavy loads...
View Article